EXACTLY HOW TO REPLACE A TUB (STEP BY STEP).

Exactly how to Replace a Tub (Step By Step).

Exactly how to Replace a Tub (Step By Step).

Blog Article

Book Now

What're your insights and beliefs on Tools You Need to Install a New Bathtub ?


How to Install a Bathtub
Mounting a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably tough job. If the old tub is readily available, the project can relocate quickly; if you need to open up a wall surface to remove the old bathtub and also position the brand-new bathtub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually qualified yourself for the work as well as fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed task, it is much better to take into consideration employing one prior to you begin. Opportunities are you may need a professional plumber to make tube links.
This article will certainly help you set up a brand-new tub in your shower room if you have already acquired a new bathtub and do not need to alter the setup of your previous water supply pipes.
Your devices and material list should comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Getting ready for the Setup


    To start with, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
    Fit the versatile tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
    Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final setting.

    Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is commonly the instance.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will come from the pipelines. When the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
    Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.

    Mounting the Tub


    Using both wooden boards under its feet, place the bath tub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
    The next goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub until the level reviews level.
    To install faucets, fit all-time low of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the other tap.
    Activate the water as well as check all joints and also new pipework for leaks as well as tighten them if necessary. Load the bathtub as well as likewise examine the overflow outlet and also the typical outlet for leakages.
    Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of a minimum of when as this will resolve it into its last position.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
    If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in location between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a stiff seal, triggering the water to permeate the wall surface in between the bath and also the tiling, leading to problems with moisture and also feasible leakages to the ceiling below.
    You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub is in usage. The sealer can break fairly early if you do not take into consideration this motion prior to securing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    Hopefully you enjoyed reading our article about How to Install a Bathtub. Thanks so much for finding the time to read our posting. Enjoyed reading our piece of writing? Please share it. Let other people discover it. Thanks a bunch for your time. Please visit our blog back soon.



    Book Your Installation

    Report this page